6 Topics You Should Know Regarding Plumbing

6 Topics You Should Know Regarding Plumbing

Most temperature adjusters are red and easily spotted, with numbers and lines much like an oven knob. Directly above the knob, you’ll find a small black arrow; it lines up with the marking on the Gordontheplumber.com Oak Brook IL Dupage County control knob itself. This indicates the current temperature (depending on the make and model of the water heater, it may also be labeled cold, warm, hot, or similar). It may also have specific settings notated with different colored lines (generally white at 110 degrees and black at 120 degrees). To get the temperature just right, turn the control knob counterclockwise to lower the temperature, or clockwise to increase the temperature. And never turn the control knob past the maximum temperature. High temperatures have been known to increase the likelihood of scalding after just one second of exposure; in fact, the American Burn Association reports that over 300,000 admissions to burn centers and emergency rooms are a result of scalding. A word of advice: many manufacturers preset the thermostat at or above 140 degrees fahrenheit. However, most homes only need to be set at 120-130 degrees. At 140 degrees, scalding can occur within five seconds ; however, at 130 degrees, scalding won’t happen until just under one minute—long after you or your loved ones have decided “it’s getting hot in here” and stepped out of the shower. Plus, at 130 degrees, water is hot enough for optimum cleaning and for removing bacteria in a dishwasher .

https://www.expresssewer.com/blog/how-to-quickly-and-safely-adjust-your-water-heater-temperature

Plumbing. It is everywhere. The plumbing system in your house is a network of pipes and fittings. It’s true that several minor concerns with plumbing systems can be handled without calling a professional. Check out these plumbing tips before you start your DIY plumbing project. Since plumbing usually does not involve electricity, many people don’t think to turn off the electricity. Keep in mind that water and electricity don’t mix. This is especially important if you are doing something near a power source. Never work on a water heater, or garbage disposal with the power connected. Protect your eyes when cutting into things.

http://www.expressplumbingidaho.com/blog/top-five-plumbing-tips/

You are here: Home / How-To-Fix Videos / Bathtub Drain Stopper / Trip Waste Assembly Bathtub Drain Stopper / Trip Waste Assembly The Bathtub Drain Stopper / Trip Waste Assembly is found in countless bathrooms across the country and it’s basically a fool proof way of filling your bathtub when taking a bath. Right? Well maybe… Prior to this modern method of keeping your bath water in the tub, many homes use to have “ Standing Waste & Overflow ” a tall cylindrical barrel standing next to the tub with an interior plunger which allowed you to stop the water so you could bathe. Drop  the plunger down and it stopped the water, lift it up and the water would drain. They were eventually phased out (although thousands are still in service today) because they simply are no longer code compliant in most municipalities across the country. Enter the modern Trip Waste Assembly a simple device which can easily be operated by a flick of a lever located in the bathtubs overflow. Flick it up and the water stops, flick it down and the water drains. Generally trouble free but as time goes by hair, soap scum and variety of mysterious childrens toys make their way into the drain and interfere with plunger causing it to hang up or not operate at all. In addition the linkage that connects the plunger to the trip lever up top gets loose or completely disconnected. When this happens some minor (or major) adjustments will be required by removing the overflow plate / trip lever assembly and exploring exactly what the issue could be. The overflow is also the access through which you would run an electric snake in the event of a complete tub blockage.

http://www.bobsplumbingvideos.com/in-this-bathtub-drain-stopper-trip-waste-assembly-tutorial-i-demonstrate-how-the-entire-assembly-functions-and-what-to-look-out-for-when-removing-the-overflow-trip-lever-plate/

You may also be interested to read

Posted in